ICD-10 Code T23.062

Burn of unspecified degree of back of left hand

Version 2019 Non-Billable Code
ICD-10:T23.062
Short Description:Burn of unspecified degree of back of left hand
Long Description:Burn of unspecified degree of back of left hand

Not Valid for Submission

ICD-10 T23.062 is a "header" nonspecific and non-billable code code, consider using a code with a higher level of specificity for a diagnosis of burn of unspecified degree of back of left hand. The code is NOT valid for the year 2019 for the submission of HIPAA-covered transactions.

Consider the following ICD-10 codes with a higher level of specificity:

  • T23.062A - Burn of unspecified degree of back of left hand, initial encounter
  • T23.062D - Burn of unspecified degree of back of left hand, subsequent encounter
  • T23.062S - Burn of unspecified degree of back of left hand, sequela

Code Classification

  • Injury, poisoning and certain other consequences of external causes (S00–T98)
    • Burns and corrosions of external body surface, specified by site (T20-T25)
      • Burn and corrosion of wrist and hand (T23)

Information for Medical Professionals

Diagnostic Related Groups

The Diagnostic Related Groups (DRGs) are a patient classification scheme which provides a means of relating the type of patients a hospital treats. The DRGs divides all possible principal diagnoses into mutually exclusive principal diagnosis areas referred to as Major Diagnostic Categories (MDC). The diagnosis code T23.062 is grouped in the following groups for version MS-DRG V36.0 applicable from 10/01/2018 through 09/30/2019.

  • 604 - TRAUMA TO THE SKIN, SUBCUTANEOUS TISSUE AND BREAST WITH MCC
  • 605 - TRAUMA TO THE SKIN, SUBCUTANEOUS TISSUE AND BREAST WITHOUT MCC
  • 949 - AFTERCARE WITH CC/MCC
  • 950 - AFTERCARE WITHOUT CC/MCC

Index to Diseases and Injuries

The Index to Diseases and Injuries is an alphabetical listing of medical terms, with each term mapped to one or more ICD-10 code(s). The following references for the code T23.062 are found in the index:


Information for Patients


Burns

A burn is damage to your body's tissues caused by heat, chemicals, electricity, sunlight, or radiation. Scalds from hot liquids and steam, building fires and flammable liquids and gases are the most common causes of burns. Another kind is an inhalation injury, caused by breathing smoke.

There are three types of burns:

  • First-degree burns damage only the outer layer of skin
  • Second-degree burns damage the outer layer and the layer underneath
  • Third-degree burns damage or destroy the deepest layer of skin and tissues underneath

Burns can cause swelling, blistering, scarring and, in serious cases, shock, and even death. They also can lead to infections because they damage your skin's protective barrier. Treatment for burns depends on the cause of the burn, how deep it is, and how much of the body it covers. Antibiotic creams can prevent or treat infections. For more serious burns, treatment may be needed to clean the wound, replace the skin, and make sure the patient has enough fluids and nutrition.

NIH: National Institute of General Medical Sciences

  • Burns (Medical Encyclopedia)
  • Chemical burn or reaction (Medical Encyclopedia)
  • Minor burns - aftercare (Medical Encyclopedia)
  • Skin graft (Medical Encyclopedia)

[Read More]

ICD-10 Footnotes

General Equivalence Map Definitions
The ICD-10 and ICD-9 GEMs are used to facilitate linking between the diagnosis codes in ICD-9-CM and the new ICD-10-CM code set. The GEMs are the raw material from which providers, health information vendors and payers can derive specific applied mappings to meet their needs.

  • Approximate Flag - The approximate flag is on, indicating that the relationship between the code in the source system and the code in the target system is an approximate equivalent.
  • No Map Flag - The no map flag indicates that a code in the source system is not linked to any code in the target system.
  • Combination Flag - The combination flag indicates that more than one code in the target system is required to satisfy the full equivalent meaning of a code in the source system.