Information for Patients
Dislocations are joint injuries that force the ends of your bones out of position. The cause is often a fall or a blow, sometimes from playing a contact sport. You can dislocate your ankles, knees, shoulders, hips, elbows and jaw. You can also dislocate your finger and toe joints. Dislocated joints often are swollen, very painful and visibly out of place. You may not be able to move it.
A dislocated joint is an emergency. If you have one, seek medical attention. Treatment depends on which joint you dislocate and the severity of the injury. It might include manipulations to reposition your bones, medicine, a splint or sling, and rehabilitation. When properly repositioned, a joint will usually function and move normally again in a few weeks. Once you dislocate a shoulder or kneecap, you are more likely to dislocate it again. Wearing protective gear during sports may help prevent dislocations.
- Dislocated shoulder - aftercare
- Kneecap dislocation
- Kneecap dislocation - aftercare
- Nursemaid's elbow
Foot Injuries and Disorders
Each of your feet has 26 bones, 33 joints, and more than 100 tendons, muscles, and ligaments. No wonder a lot of things can go wrong. Here are a few common problems:
- Bunions - hard, painful bumps on the big toe joint
- Corns and calluses - thickened skin from friction or pressure
- Plantar warts - warts on the soles of your feet
- Fallen arches - also called flat feet
Ill-fitting shoes often cause these problems. Aging and being overweight also increase your chances of having foot problems.
- Claw foot
- Clubfoot repair
- Common peroneal nerve dysfunction
- Extremity x-ray
- Flat feet
- Foot pain
- Foot sprain - aftercare
- Foot, leg, and ankle swelling
- Hand or foot spasms
- High arch
- Leg or foot amputation
- Metatarsal fracture (acute) - aftercare
- Metatarsal stress fractures - aftercare
- Metatarsus adductus
- Morton's neuroma
General Equivalence Map Definitions
The ICD-9 and ICD-10 GEMs are used to facilitate linking between the diagnosis codes in ICD-9-CM and the new ICD-10-CM code set. The GEMs are the raw material from which providers, health information vendors and payers can derive specific applied mappings to meet their needs.
- Approximate Flag - The approximate flag is on, indicating that the relationship between the code in the source system and the code in the target system is an approximate equivalent.
- No Map Flag - The no map flag indicates that a code in the source system is not linked to any code in the target system.
- Combination Flag - The combination flag indicates that more than one code in the target system is required to satisfy the full equivalent meaning of a code in the source system.
Index of Diseases and Injuries Definitions
- And - The word "and" should be interpreted to mean either "and" or "or" when it appears in a title.
- Code also note - A "code also" note instructs that two codes may be required to fully describe a condition, but this note does not provide sequencing direction.
- Code first - Certain conditions have both an underlying etiology and multiple body system manifestations due to the underlying etiology. For such conditions, the ICD-10-CM has a coding convention that requires the underlying condition be sequenced first followed by the manifestation. Wherever such a combination exists, there is a "use additional code" note at the etiology code, and a "code first" note at the manifestation code. These instructional notes indicate the proper sequencing order of the codes, etiology followed by manifestation.
- Type 1 Excludes Notes - A type 1 Excludes note is a pure excludes note. It means "NOT CODED HERE!" An Excludes1 note indicates that the code excluded should never be used at the same time as the code above the Excludes1 note. An Excludes1 is used when two conditions cannot occur together, such as a congenital form versus an acquired form of the same condition.
- Type 2 Excludes Notes - A type 2 Excludes note represents "Not included here". An excludes2 note indicates that the condition excluded is not part of the condition represented by the code, but a patient may have both conditions at the same time. When an Excludes2 note appears under a code, it is acceptable to use both the code and the excluded code together, when appropriate.
- Includes Notes - This note appears immediately under a three character code title to further define, or give examples of, the content of the category.
- Inclusion terms - List of terms is included under some codes. These terms are the conditions for which that code is to be used. The terms may be synonyms of the code title, or, in the case of "other specified" codes, the terms are a list of the various conditions assigned to that code. The inclusion terms are not necessarily exhaustive. Additional terms found only in the Alphabetic Index may also be assigned to a code.
- NEC "Not elsewhere classifiable" - This abbreviation in the Alphabetic Index represents "other specified". When a specific code is not available for a condition, the Alphabetic Index directs the coder to the "other specified” code in the Tabular List.
- NOS "Not otherwise specified" - This abbreviation is the equivalent of unspecified.
- See - The "see" instruction following a main term in the Alphabetic Index indicates that another term should be referenced. It is necessary to go to the main term referenced with the "see" note to locate the correct code.
- See Also - A "see also" instruction following a main term in the Alphabetic Index instructs that there is another main term that may also be referenced that may provide additional Alphabetic Index entries that may be useful. It is not necessary to follow the "see also" note when the original main term provides the necessary code.
- 7th Characters - Certain ICD-10-CM categories have applicable 7th characters. The applicable 7th character is required for all codes within the category, or as the notes in the Tabular List instruct. The 7th character must always be the 7th character in the data field. If a code that requires a 7th character is not 6 characters, a placeholder X must be used to fill in the empty characters.
- With - The word "with" should be interpreted to mean "associated with" or "due to" when it appears in a code title, the Alphabetic Index, or an instructional note in the Tabular List. The word "with" in the Alphabetic Index is sequenced immediately following the main term, not in alphabetical order.