Information for Patients
A collapsed lung happens when air enters the pleural space, the area between the lung and the chest wall. If it is a total collapse, it is called pneumothorax. If only part of the lung is affected, it is called atelectasis.
Causes of a collapsed lung include:
- Lung diseases such as pneumonia or lung cancer
- Being on a breathing machine
- Surgery on the chest or abdomen
- A blocked airway
If only a small area of the lung is affected, you may not have symptoms. If a large area is affected, you may feel short of breath and have a rapid heart rate.
A chest x-ray can tell if you have it. Treatment depends on the underlying cause.
NIH: National Heart, Lung, and Blood Institute
Your pleura is a large, thin sheet of tissue that wraps around the outside of your lungs and lines the inside of your chest cavity. Between the layers of the pleura is a very thin space. Normally it's filled with a small amount of fluid. The fluid helps the two layers of the pleura glide smoothly past each other as your lungs breathe air in and out.
Disorders of the pleura include:
- Pleurisy - inflammation of the pleura that causes sharp pain with breathing
- Pleural effusion - excess fluid in the pleural space
- Pneumothorax - buildup of air or gas in the pleural space
- Hemothorax - buildup of blood in the pleural space
Many different conditions can cause pleural problems. Viral infection is the most common cause of pleurisy. The most common cause of pleural effusion is congestive heart failure. Lung diseases, like COPD, tuberculosis, and acute lung injury, cause pneumothorax. Injury to the chest is the most common cause of hemothorax. Treatment focuses on removing fluid, air, or blood from the pleural space, relieving symptoms, and treating the underlying condition.
NIH: National Heart, Lung, and Blood Institute
General Equivalence Map Definitions
The ICD-9 and ICD-10 GEMs are used to facilitate linking between the diagnosis codes in ICD-9-CM and the new ICD-10-CM code set. The GEMs are the raw material from which providers, health information vendors and payers can derive specific applied mappings to meet their needs.
- Approximate Flag - The approximate flag is on, indicating that the relationship between the code in the source system and the code in the target system is an approximate equivalent.
- No Map Flag - The no map flag indicates that a code in the source system is not linked to any code in the target system.
- Combination Flag - The combination flag indicates that more than one code in the target system is required to satisfy the full equivalent meaning of a code in the source system.
Index of Diseases and Injuries Definitions
- And - The word "and" should be interpreted to mean either "and" or "or" when it appears in a title.
- Code also note - A "code also" note instructs that two codes may be required to fully describe a condition, but this note does not provide sequencing direction.
- Code first - Certain conditions have both an underlying etiology and multiple body system manifestations due to the underlying etiology. For such conditions, the ICD-10-CM has a coding convention that requires the underlying condition be sequenced first followed by the manifestation. Wherever such a combination exists, there is a "use additional code" note at the etiology code, and a "code first" note at the manifestation code. These instructional notes indicate the proper sequencing order of the codes, etiology followed by manifestation.
- Type 1 Excludes Notes - A type 1 Excludes note is a pure excludes note. It means "NOT CODED HERE!" An Excludes1 note indicates that the code excluded should never be used at the same time as the code above the Excludes1 note. An Excludes1 is used when two conditions cannot occur together, such as a congenital form versus an acquired form of the same condition.
- Type 2 Excludes Notes - A type 2 Excludes note represents "Not included here". An excludes2 note indicates that the condition excluded is not part of the condition represented by the code, but a patient may have both conditions at the same time. When an Excludes2 note appears under a code, it is acceptable to use both the code and the excluded code together, when appropriate.
- Includes Notes - This note appears immediately under a three character code title to further define, or give examples of, the content of the category.
- Inclusion terms - List of terms is included under some codes. These terms are the conditions for which that code is to be used. The terms may be synonyms of the code title, or, in the case of "other specified" codes, the terms are a list of the various conditions assigned to that code. The inclusion terms are not necessarily exhaustive. Additional terms found only in the Alphabetic Index may also be assigned to a code.
- NEC "Not elsewhere classifiable" - This abbreviation in the Alphabetic Index represents "other specified". When a specific code is not available for a condition, the Alphabetic Index directs the coder to the "other specified” code in the Tabular List.
- NOS "Not otherwise specified" - This abbreviation is the equivalent of unspecified.
- See - The "see" instruction following a main term in the Alphabetic Index indicates that another term should be referenced. It is necessary to go to the main term referenced with the "see" note to locate the correct code.
- See Also - A "see also" instruction following a main term in the Alphabetic Index instructs that there is another main term that may also be referenced that may provide additional Alphabetic Index entries that may be useful. It is not necessary to follow the "see also" note when the original main term provides the necessary code.
- 7th Characters - Certain ICD-10-CM categories have applicable 7th characters. The applicable 7th character is required for all codes within the category, or as the notes in the Tabular List instruct. The 7th character must always be the 7th character in the data field. If a code that requires a 7th character is not 6 characters, a placeholder X must be used to fill in the empty characters.
- With - The word "with" should be interpreted to mean "associated with" or "due to" when it appears in a code title, the Alphabetic Index, or an instructional note in the Tabular List. The word "with" in the Alphabetic Index is sequenced immediately following the main term, not in alphabetical order.